Welcome to Fenco Group
You have no items in your shopping cart.
Filters
Search
Close

PUMPS - HIGH PRESSURE

View as Grid List
Sort by
Display per page

VT3 HIGH PRESSURE PUMP c/w gearbox 3/4"F206Bar13l

210 Bar (3050 PSI) Industrial PUMP and GEARBOX with 3/4" Shaft suitable for 3/4" horizontal shaft engines such as Loncin and HONDA GX160 . The pump is low revving which decreases wear. The flow rate of 13 litres per minute is suitable for most water mains supplies. The VT3 comes complete with unloader valve with 3/4F inlet and MSQ female outlet.
  • Note: the pressure must be set to unload at no more than 210 BAR (3050PSI). See safety note below:
  • Inlet fitting options include: MH12/12 or MH12/08 brass hose tails or B1.134 KCQ coupling. VIEW: COUPLINGS – LOW PRESSURE and COUPLINGS – QR LOW PRESSURE
  • Outlet fitting option: B14.9191 or B14.9191SS MSQ male to 3/8F coupling. VIEW: COUPLINGS – HIGH PRESSURE and COUPLINGS – QR HIGH PRESSURE
  • The VT3 pump and gearbox comes lubricated complete with V-TUF PRESSURE LUBE PL500.
  • OPTIONAL EXTRAS: C7.038BPKIT Pump priming valve kit ; E1.1013KIT PUMP SUCTION KIT (3m) ; PL500 V-TUF Pressure Lube (for pump top up)

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £491.39 incl tax £655.18 incl tax

    VT4 HIGH PRESSURE PUMP c/w gearbox 1"F250bar 15l

    250 Bar (3600 PSI) Industrial PUMP and GEARBOX with 1" Shaft suitable for 1" horizontal shaft engines such as Loncin and HONDA GX240 ; GX340 ; GX390 and YANMAR diesel engines. The pump is low revving which decreases wear. The flow rate is 15 litres per minute. The VT4 comes complete with unloader valve with 3/4F inlet and MSQ female outlet.
  • Note: the pressure must be set to unload at no more than 250 BAR (3600PSI). See safety note below:
  • Inlet fitting options include: MH12/12 or MH12/08 brass hose tails or B1.134 KCQ coupling. VIEW: COUPLINGS – LOW PRESSURE and COUPLINGS – QR LOW PRESSURE
  • Outlet fitting option: B14.9191 or B14.9191SS MSQ male to 3/8F coupling. VIEW: COUPLINGS – HIGH PRESSURE and COUPLINGS – QR HIGH PRESSURE
  • The VT4 pump and gearbox comes lubricated complete with V-TUF PRESSURE LUBE PL500.
  • OPTIONAL EXTRAS: C7.038BPKIT Pump priming valve kit ; E1.1013KIT PUMP SUCTION KIT (3m) ; PL500 V-TUF Pressure Lube (for pump top up)

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £635.29 incl tax £847.06 incl tax

    VT5 HIGH PRESSURE PUMP 3/4"F 190 Bar 13L

    190 Bar (2800 PSI) Industrial Pump with 3/4" Shaft suitable for 3/4" horizontal shaft engines such as Loncin and HONDA GX160 . The flow rate of 13 litres per minute is suitable for most water mains supplies. The VT5 comes complete with unloader valve with 3/4F inlet and MSQ female outlet.
  • Note: the pressure must be set to unload at no more than 190 BAR (2800PSI). See safety note below:
  • Inlet fitting options include: MH12/12 or MH12/08 brass hose tails or B1.134 KCQ coupling. VIEW: COUPLINGS – LOW PRESSURE and COUPLINGS – QR LOW PRESSURE
  • Outlet fitting option: B14.9191 or B14.9191SS MSQ male to 3/8F coupling. VIEW: COUPLINGS – HIGH PRESSURE and COUPLINGS – QR HIGH PRESSURE
  • The VT5 pump comes lubricated complete with V-TUF PRESSURE LUBE PL500.
  • OPTIONAL EXTRAS: C7.038BPKIT Pump priming valve kit ; E1.1012KIT PUMP SUCTION KIT (2m) ; PL500 V-TUF Pressure Lube (for pump top up)
  • Suitable replacement pump for WW909 PUMPS ; WW907 ; WS430110057-s PUMPS engine mounted pumps.

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £357.22 incl tax £476.28 incl tax

    VT6 HIGH PRESSURE PUMP 1"F 206 Bar 15L

    V-TUF VT6 206 Bar (3030 PSI) Industrial Pump with 1" Shaft suitable for 1" horizontal shaft engines such as Loncin and HONDA GX240 ; GX340 ; GX390 and YANMAR diesel engines. The flow rate is 15 litres per minute. The VT6 comes complete with unloader valve with 3/4F inlet and MSQ female outlet.
  • Note: the pressure must be set to unload at no more than 206 BAR (3030PSI). See safety note below:
  • Inlet fitting options include: MH12/12 or MH12/08 brass hose tails or B1.134 KCQ coupling. VIEW: COUPLINGS – LOW PRESSURE and COUPLINGS – QR LOW PRESSURE
  • Outlet fitting option: B14.9191 or B14.9191SS MSQ male to 3/8F coupling. VIEW: COUPLINGS – HIGH PRESSURE and COUPLINGS – QR HIGH PRESSURE
  • The VT6 pump comes lubricated complete with V-TUF PRESSURE LUBE PL500.
  • OPTIONAL EXTRAS: C7.038BPKIT Pump priming valve kit ; E1.1013KIT PUMP SUCTION KIT (3m) ; PL500 V-TUF Pressure Lube (for pump top up)

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £367.67 incl tax £490.22 incl tax

    GEARBOX - FOR UP TO 18HP ENGINES, 1" SHAFT

    V-TUF RL400 REDUCTION GEARBOX for 1" horizontal shaft engines and pumps with 24mm shafts with 4 x 8mm bolt hole mount and 61mm between centres. Other order codes: WS430110029-s
  • 1:2.24 reduction.
  • Suited to pumps: XHDM300 ; XHDM350; XHDM400, XHDM450; WS201.
  • Suited to engines: GX240QX ; GX390QX ; VLCP15 ; VLCD07 ; VLCD15 .
  • Recommended oil: PRESSURE LUBE PL500
  • £340.18 incl tax

    PUMP & MOTOR - 12L/min @ 100Bar (1500psi) 240v TS

    12L/min 100BAR LOW-REV HEAVY DUTY 170 bar rated Pump & Motor 240V - TSS - MH.243 + XHDM151 + C0.063 + I2.016 + I2.110 + (M8x25) x 4 + I3.325 x5
    £1,341.46 incl tax

    PUMP VT7 - 12L @ 200BAR, 1450RPM, 28mm 'H' SHAFT

    V-TUF VT7 HIGH PRESSURE PUMP 200 Bar (3000 PSI); 12 litres per minute, Industrial Pump with 28mm HOLLOW Shaft. This pump has the perfect balance of pressure and flow for optimal cleaning performance.

    Suitable for electric 28mm solid shaft shaft motors such as the MS.243 (240 volt) motor to run with a 05 jet or MS.4155 (415 volt) motor to run with a smaller jet for at pressures closer to 200 Bar , MS.113 (110 volt) motor with a 07 jet, (ALWAYS MAKE SURE the motor is running at least 15% within its maximum amperage).

    Most mains water supplies can cope with flow rate of 12 litres per minute.
  • The V-TUF VT7 is supplied unloader valve. This pump MUST be fitted with an unloader valve.
  • 2 x Inlet 1/2F bsp ports – one ½F bsp port is supplied with a thermal overload.
  • 2 x Outlet 3/8F bsp ports - one ½F bsp port is supplied with a blanking plug
  • The VT7 pump comes lubricated complete with V-TUF PRESSURE LUBE PL500.
  • OPTIONAL EXTRAS: PL500 V-TUF Pressure Lube (for pump top up)
  • Note: the pressure must be set to unload at no more than 200 BAR (3000PSI). See safety note below:

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £594.00 incl tax

    PUMP XHDM400SS - 15L @ 200BAR, 1450RPM, MALE SHAFT

    V-TUF XHDM400SS Super Series HIGH PRESSURE PUMP 200 Bar (3000 PSI); 15 litres per minute, Industrial Pump with 24mm SOLID Shaft. This pump has the perfect balance of pressure and flow for optimal cleaning performance on 415 volt motors; and the 9HP to 15HP petrol and diesel engines with RL400 gearbox. (Scroll down and see RELATED PRODUCTS below)

    100% manufactured in the EU which give you the confidence that all materials and design are to give you the greatest return on your investment.

    The XHDM400SS PUMP units are very popular in the Carwash industry, the Contractor and Hire Industry and Agricultural contract cleaning industry.

    SUPER Robustly made with a perfect balance of weight to ensure minimum fatigue on motor and gearbox mountings.

    The XHDM400SS pump comes lubricated complete with equipment ‘lifetime enhancer’ V-TUF PRESSURE LUBE PL500 with a molecular content of MSM (Metal Surface Modifier) reducing friction to basically zero - less heat and less wear.

    Suitable for electric 24mm hollow shaft electric 415 volt motors such as MH.4155 (pressure max 150 bar) & MH.4175 (pressure max 200bar) motors. (ALWAYS MAKE SURE the motor is running at least 15% within its maximum amperage).

    Most mains water supplies cannot cope with 15 litres so it may be advisable to run these units on suction out a water butt if you are unsure.
  • The V-TUF XHDM400SS is NOT supplied unloader valve. This pump MUST be fitted with an unloader valve.
  • 2 x Inlet 1/2F bsp ports – one ½F bsp port is blanked
  • 2 x Outlet 3/8F bsp ports - one ½F bsp port is supplied with a blanking plug
  • OPTIONAL EXTRAS: PL500 V-TUF Pressure Lube (for pump top up)
  • Suitable replacement for the following pumps: INTERPUMP WS201 , V-TUF VT301 ; AR RK 15.20H ; V-TUF XHDM400
  • Note: the pressure must be set to unload at no more than 200 BAR (3000PSI). See safety note below:

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be blown clean out of their threads which cause dangerous projectiles. Please be free to ring 01522 787978 if you need any assistance.
  • £1,152.84 incl tax

    PUMP XHDM450SS - 21L @ 200BAR, 1450RPM, MALE SHAFT

    V-TUF XHDM450SS Super Series HIGH PRESSURE PUMP 200 Bar (3000 PSI); 21 litres per minute, Industrial Pump with 24mm SOLID Shaft. This pump has the perfect balance of pressure and flow for optimal cleaning performance where fast rinse is needed or bulk dirt needs shifting; often used on 415 volt motors; and the 10HP to 15HP petrol and diesel engines with RL400 gearbox. (Scroll down and see RELATED PRODUCTS below)

    100% manufactured in the EU which give you the confidence that all materials and design are to give you the greatest return on your investment.

    The XHDM450SS PUMP units are very popular in the Carwash industry, the Contractor and Hire Industry and Agricultural contract cleaning industry.

    SUPER Robustly made with a perfect balance of weight to ensure minimum fatigue on motor and gearbox mountings.

    The XHDM400SS pump comes lubricated complete with equipment ‘lifetime enhancer’ V-TUF PRESSURE LUBE PL500 with a molecular content of MSM (Metal Surface Modifier) reducing friction to basically zero - less heat and less wear.

    Suitable for electric 24mm hollow shaft electric 415 volt motors such as MH.4175 (pressure max 150bar) motor. (ALWAYS MAKE SURE the motor is running at least 15% within its maximum amperage).

    Mains water supplies cannot cope with 21 litres so it is strongly advisable to run these units on suction from a bulk water supply.
  • The V-TUF XHDM450SS is NOT supplied unloader valve. This pump MUST be fitted with an unloader valve.
  • 2 x Inlet 1/2F bsp ports – one ½F bsp port is blanked
  • 2 x Outlet 3/8F bsp ports - one ½F bsp port is supplied with a blanking plug
  • OPTIONAL EXTRAS: PL500 V-TUF Pressure Lube (for pump top up)
  • Suitable replacement for the following pumps: INTERPUMP WS202 , AR RK 21.20H ; V-TUF XHDM450
  • Note: the pressure must be set to unload at no more than 200 BAR (3000PSI). See safety note below:

    IMPORTANT SAFETY NOTE: BEFORE powering the system: 1. the unloader valve MUST be set at MINIMUM pressure; 2. The bypass port MUST be open; 3. Then set the unloader to the required pressure (which MUST be LESS than the maximum unloader pressure of the unloader valve AND LESS than the maximum pressure of your equipment); 4. Set the locking nuts so this pressure (the running pressure and the lock line pressure) cannot be exceeded.
  • CAUTION: This is high pressure equipment and if the above safety and set up rules are not followed, serious damage to equipment and injury to humans can occur. The caps and joints can be
  • £1,227.60 incl tax
    Close